Build a sous-vide cooker with your Bean! Make delicious food and leverage the power of Bluetooth Low Energy to control your cooking experience.
"Sous-vide (French for "under vacuum") is a method of cooking food sealed in airtight plastic bags in a water bath or in a temperature-controlled steam environment for longer than normal cooking times at an accurately regulated temperature much lower than normally used for cooking. The intention is to cook the item evenly, ensuring that the inside is properly cooked without overcooking the outside, and retain moisture."
Once you start cooking your food sous-vide, you'll never go back—everything comes out moist and delicious and falls apart on your fork. It's great for cooking everything from salmon to steak to squash.
This tutorial assumes you have completed the Getting Started guide and that you understand how to upload a sketch to Bean using Bean Loader.
You need either a Bean OR a Bean+ for this project.
A LightBlue Bean or Bean+, regulates the temperature and talks to your phone.
Commercial sous-vide solutions for home chefs (such as the Sansaire) usually include the following:
Temperature sensor Heating coil Water circulator Instead of a heating coil, this DIY sous-vide machine uses a slow cooker (crock pot) to heat the water and cook the food. Since the stoneware in the slow cooker distributes heat evenly to the contents of the cooker, we won't need to include a water circulator.
Slow cooker We picked a Hamilton Beach 8-quart slow cooker from Amazon. Whatever cooker you use, make sure it's an analog control mechanism—no fancy digital temperature regulators or timers. The Bean is only able to turn the cooker on and off with a relay, and power-cycling a digital cooker will most likely cause it to stop cooking until it's set up again.
Power relay To turn the slow cooker on and off and keep the water at the desired temperature, we bought an AC relay device called the PowerSwitch Tail II from Sparkfun. We selected the PowerSwitch Tail II because it let us use the Bean to control AC power in a safe way. This relay is fully isolated and allows us to use low-voltage, low-current signals to turn the slow cooker on and off.
Temperature sensor To measure the temperature of the water, we ordered a DS18B20 temperature sensor with waterproof enclosure from Sparkfun. You could use any waterproof temperature sensor you want, but the Arduino code included with this project uses the DS18B20 because it's an accurate, reliable, and inexpensive temperature sensor.
This sensor relies on a pullup resistor to enable communication via the 1-Wire protocol. We used a 10k resistor, but most large resistors (>1kΩ) will work.
Battery pack Finally, we hooked our Bean up to one of the 2xAA battery packs included in the Maker Kit and attached it with a bit of double-sided sticky foam. We connected this because polling a temperature sensor and talking to an iOS device every 5 seconds will quickly drain a coin cell battery.
We'll use an iOS device that supports Bluetooth Low Energy with an app that talks to the Bean and sets the target temperature for the cooker.
VCC/GND: Drawing power from the 2xAA battery pack (
BAT/GND: Powering the DS18B20 temperature sensor (
2: Connected to the DS18B20 temperature sensor's data line (the white wire)
3: Connected to the PowerSwitch Tail II
GND: Connected to the PowerSwitch Tail II
-in(pin 2) 4.7k resistor: Connected between Bean
BATand Bean IO pin
2(pullup on the DS18B20 data line)
You'll need to rename your Bean using the OS X Loader App. The iOS app finds the Sous Vide Bean by looking for a nearby Bean with the name
SousVide— if your Bean isn't named exactly the same, the iOS app won't try to connect.
Alternately, you can change the name that the app searches for inside
Sous Vide/Controllers/SVViewController.m to match your Bean instead:
// Which Bean to connect to (BLE local name) #define SOUS_VIDE_BEAN_NAME @"SousVide"
Open the sketch at
sous_vide_arduino/sous_vide_arduino.ino in the Arduino software, verify it, and program your Bean with the sketch.
This sketch relies on the OneWire library by PJRC and the Dallas Temperature library by Miles Burton. You need to install those libraries into your Arduino software before Verifying the sketch.
Clone this repository and open
Sous Vide.xcworkspace in Xcode. Once that's complete, build and run the app on your iPhone or iPod Touch.
The iOS simulator doesn't support Bluetooth Low Energy, so you'll need to have actual hardware to use the app properly. You'll also need an iOS Developer Program account to be able to run the app on your device.
You can verify the Bean is working properly by running the iOS app and connecting to the Bean. You should connect the temperature sensor and relay to the Bean, but you don't have to plug the slow cooker or the relay into the wall—the relay has an LED that indicates its powered/unpowered status.
Once the iOS app connects to the Bean, you should be able to read the current temperature of the sensor. If you turn on the "Cooking" switch and set the target temperature higher than the current temperature with the slider, you should see the Bean turn on the relay (the red LED on the relay should come on) in an attempt to heat the water in the slow cooker to the target temperature.
It's worth taking a little bit of time to verify the Bean is able to moderate the temperature of the slow cooker within reasonable bounds—in our experience, the temperature has stayed within ±2°F, but your results will vary based on the cooker you use.
Don't forget basic safety—slow cookers generate heat, so make sure to monitor your setup while you're cooking to avoid any risk of fire!
UI glitches Sometimes the app will disconnect from the Bean but show that it's still connected, or disconnect from the Bean but fail to scan for nearby Beans to reconnect. The current workarounds are to cycle Bluetooth power on your iOS device or to force quit the app and reopen it.
Periodic disconnects The iOS app frequently loses connection to the Bean. This won't affect your cooking—the Bean holds the last-set values in memory and continues to use them to regulate the temperature of the water in the cooker.
If you have any questions about this project, the best place to ask is the Beantalk community forum.
All aspects of this project are covered under the MIT License.